Technical News
  • New chip captures power from multiple sources [기술]
  • 심준보 (IP: *.104.135.112)
    조회 수: 58009, 추천 수: 0/0, 2012.07.10 08:52:56
  • New chip captures power from multiple sources
    Graphic: Christine Daniloff
    System developed at MIT could combine power harvested from light, heat and
    vibrations to run monitoring systems.

    Researchers at MIT have taken a significant step
    toward battery-free monitoring systems — which
    could ultimately be used in biomedical devices,
    environmental sensors in remote locations and
    gauges in hard-to-reach spots, among other

    Previous work from the lab of MIT professor Anantha Chandrakasan has focused on the development of
    computer and wireless-communication chips that can operate at extremely low power levels, and on a variety of
    devices that can harness power from natural light, heat and vibrations in the environment.
    The latest development, carried out with doctoral student Saurav Bandyopadhyay, is a chip that could harness
    all three of these ambient power sources at once, optimizing power delivery.

    The energy-combining circuit is described in a paper being published this summer in theIEEE Journal of
    Solid-State Circuits.

    “Energy harvesting is becoming a reality,” says Chandrakasan, the Keithley Professor of Electrical Engineering
    and head of MIT’s Department of Electrical Engineering and Computer Science. Low-power chips that can collect
    data and relay it to a central facility are under development, as are systems to harness power from
    environmental sources. But the new design achieves efficient use of multiple power sources in a single device,
    a big advantage since many of these sources are intermittent and unpredictable.

    “The key here is the circuit that efficiently combines many sources of energy into one,” Chandrakasan says.
    The individual devices needed to harness these tiny sources of energy — such as the difference between body
    temperature and outside air, or the motions and vibrations of anything from a person walking to a bridge
    vibrating as traffic passes over it — have already been developed, many of them in Chandrakasan’s lab.

    Combining the power from these variable sources requires a sophisticated control system, Bandyopadhyay
    explains: Typically each energy source requires its own control circuit to meet its specific requirements.
    For example, circuits to harvest thermal differences typically produce only 0.02 to 0.15 volts, while low-power
    photovoltaic cells can generate 0.2 to 0.7 volts and vibration-harvesting systems can produce up to 5 volts.
    Coordinating these disparate sources of energy in real time to produce a constant output is a tricky process. 

    So far, most efforts to harness multiple energy sources have simply switched among them, taking advantage of
    whichever one is generating the most energy at a given moment, Bandyopadhyay says, but that can waste the
    energy being delivered by the other sources. “Instead of that, we extract power from all the sources,” he says.
    The approach combines energy from multiple sources by switching rapidly between them.

    Another challenge for the researchers was to minimize the power consumed by the control circuit itself, to leave
    as much as possible for the actual devices it’s powering — such as sensors to monitor heartbeat, blood sugar,
    or the stresses on a bridge or a pipeline. The control circuits optimize the amount of energy extracted from each

    The system uses an innovative dual-path architecture. Typically, power sources would be used to charge up a
    storage device, such as a battery or a supercapacitor, which would then power an actual sensor or other circuit.
    But in this control system, the sensor can either be powered from a storage device or directly from the source,
    bypassing the storage system altogether. “That makes it more efficient,” Bandyopadhyay says. The chip uses a
    single time-shared inductor, a crucial component to support the multiple converters needed in this design, rather
    than separate ones for each source.  

    David Freeman, chief technologist for power-supply solutions at Texas Instruments, who was not involved in this
    work, says, “The work being done at MIT is very important to enabling energy harvesting in various environments.
    The ability to extract energy from multiple different sources helps maximize the power for more functionality from
    systems like wireless sensor nodes.”

    Only recently, Freeman says, have companies such as Texas Instruments developed very low-power
    microcontrollers and wireless transceivers that could be powered by such sources. “With innovations like these
    that combine multiple sources of energy, these systems can now start to increase functionality,” he says.
    “The benefits from operating from multiple sources not only include maximizing peak energy, but also help when
    only one source of energy may be available.”

    The work has been funded by the Interconnect Focus Center, a combined program of the Defense Advanced
    Research Projects Agency and companies in the defense and semiconductor industries.

댓글 0 ...

  Today 0, Yesterday 0, Total 93
93 기술 심준보 0 56757 2012.09.26
92 기술 라종현 0 57351 2012.07.12
기술 심준보 0 58009 2012.07.10
90 기술 심준보 0 58639 2012.06.14
89 기술 심준보 0 57282 2012.06.08
88 기술 정일형 0 62087 2012.06.01
87 기술 Minseok Shin 0 57266 2012.06.01
86 기술 심준보 0 58953 2012.06.01
85 기술 Minseok Shin 0 57471 2012.05.31
84 기술 심준보 0 57738 2012.05.29
83 기술 심준보 0 57881 2012.05.23
82 기술 심준보 0 59495 2012.05.23
81 기술 심준보 0 53546 2012.05.21
80 기술 Minseok Shin 0 57116 2012.05.19
79 기술 라종현 0 57937 2012.05.19
78 기술 심준보 0 57358 2012.05.17
77 기술 심준보 0 57860 2012.05.17
76 기술 심준보 0 57900 2012.05.14
75 기술 심준보 0 58935 2012.05.12
74 기술 심준보 0 58765 2012.05.07